JTY cable assembly with a right-angle circular connector, a transparent modular plug and a coiled black cable

Waterproof Harness Types

Waterproof cable assemblies

Connector-to-Connector Cable

Complete JTY coiled black cable with a right-angle circular connector and a transparent modular plug

Right-angle circular connector and modular plug on one continuous cable. It links an outdoor unit to a controller or network port.

Connector-to-Connector Waterproof Cable Assemblies

Coiled black JTY cable with a modular plug and a right-angle circular connector

This example has a straight modular plug and an angled circular connector on one continuous jacketed cable.

Straight modular end

The modular end has a straight cable exit. Specify its mating reference and wiring assignment; the visible plug shape does not identify a network protocol.

Angled circular end

The circular end turns across the cable route. Match its keying, mating reference and exit orientation before assigning the assembled connection a protection requirement.

Define the protection requirement

Connection state
Mated, unmated or capped
Protection scope
Connector pair, cable entry and finished assembly
Acceptance evidence
Required test method and conditions

The product photograph does not establish an IP grade or network protocol. Protection and electrical requirements belong to the selected finished assembly.

Specify the complete connection

Mating and cable route

Both mating references should be specified, keying and the required wiring map. Define cable length between agreed end datums and the circular connector exit direction so the assembly drawing describes the installed route.

Sealing and included parts

List the required connection state, cable entry and any cap or sealing accessory in the enquiry. The quotation and acceptance specification should state which supplied parts and assembled conditions the protection requirement covers.

Send your drawing

Water Exposure by Application

ApplicationWater exposureRating to ask for
Electric two- and three-wheelers, balance vehiclesRain, road sprayIP67 at every exposed connector
Outdoor lightingRain, brief flooding at ground levelIP67 at the fixture connector
Landscape fountainsSplash above the waterline, continuous immersion below itIP67 above the waterline. IP68, with depth and duration stated, for submerged fittings
DronesRain and spray in flightIP67 at every exposed connector
Smart appliancesSplashes, condensationIP67 at connectors near water

Buyers who pressure-wash the equipment list it on the enquiry as a separate IPX9 requirement.

Connector Ends, Caps and Panel Flanges

Complete JTY harness with a rectangular connector at the left and a circular connector plus open wire leads at the lower right; the sheath ends above the separated wires
Mixed-end assembly with a rectangular connector, a circular connector and open leads.
ARectangular connector end
Stays on the dry side inside the equipment and needs no seal of its own.
BCircular threaded connector
The threaded coupling secures the circular connector. Vibration resistance depends on the connector and locking arrangement.
Detail of the same JTY harness: black cable sheath ends where coloured individual wires emerge
Detail of the same JTY harness showing the circular connector and exposed metal at the red and black wire ends
JTY metal-flange circular interface with tethered cap at the lower left and rear leads ending in white and black connector housings at the upper right; no panel is fitted
Metal flange socket with tethered cap and rear leads.
CPanel flange
Seals to the device wall with a gasket under four screws.
DTethered cap
Protection of an unmated socket depends on the specified rating with the matching cap fitted. The tether keeps the cap on the harness during maintenance.

Cable entry

The cable-entry seal is sized to the jacket of the cable on your drawing or sample. Changes to the cable need a sealing-fit review and may require a different entry part.

Lengths and Tails

Connector to open leads

Complete JTY assembly with a circular connector, coiled sheathed cable and red and black open wire tails; R marks the connector end, S the jacket stop, and T the wire tips
R · Connector reference   S · Jacket stop   T · Wire tips

Finished length runs from the connector datum R to each wire tip T.

The jacket stop S sets the free wire left for termination, and stripped tails also carry a strip length.

Flange to multiple tails

Complete JTY metal-flange assembly with tethered cap and three connector-ended rear tails; P identifies the flange reference, T1 and T2 the two white housings, and T3 the black housing
P · Flange reference   T1 / T2 · White housings   T3 · Black housing

Each rear tail has its own length from the flange datum P to its end housing. The three ends can sit at three different boards.

Quotes follow the R–T and P–T lengths on the drawing.

Build and Electrical Checks

More than 30 vertical injection molding machines run in JTY's plant, alongside its automatic terminal machines.

Crimping and assembly

Terminals are crimped on automatic terminal machines. Housings and seals are fitted at assembly benches before each connector is closed.

Buyers approve the first samples against a crimp cross-section report that ships with them.

JTY operator positioning wire terminals at a bench crimping press
Terminal crimping
JTY operators assembling connector components at a workbench
Connector assembly

Electrical checks

Continuity, miswiring, resistance and withstand voltage are tested at JTY's test stations.

JTY operator using a precision resistance measurement instrument at a test station
Resistance measurement
JTY operator at a withstand-voltage test station
Withstand-voltage testing

Waterproof Wire Harness FAQ

Can JTY copy a harness we already use?

JTY measures the pin connections, wire lengths and parts on your sample and returns them as a drawing. Production follows the version you approve.

Which environmental tests can JTY run on samples?

Salt-spray, temperature and humidity testing, and high and low temperature aging run in JTY's own test chambers. UV exposure belongs on the test request as a separate item.

Does a custom waterproof harness need new tooling?

Harnesses built on standard sealed connectors need no new mold. A custom molded end is made in JTY's own molding workshop.

Contact Us

Name the device, where the harness meets water, each connector part number and the R–T or P–T lengths, or send a sample.

    No file selected

    PDF, XLSX, CSV, JPG or PNG · up to 5 MB. Need an NDA? Mention it above.

    Samples in 3–7 days. Batch production about 30 days after order confirmation.

    * Required fields

    Concept illustration of a wire harness sample beside a drawing and inspection checklistYour Project
    PRODUCT CONCEPT