Red and black JTY cable assembly with a gray two-pole connector and ring terminals

Connector, wire harness & cable assembly manufacturer

JTY makes its own connectors, crimps the terminals and molds the cable exits in the same plant. Samples are ready in 3–7 days. You fit the sample in your equipment before batch production starts.

Our Company

JTY Connector was founded in 2015. In 2021, the company began developing and producing harnesses for new energy applications. JTY works with equipment manufacturers from prototype development to batch production.

JTY makes its own energy storage connectors and bolt connectors. JTY also builds wire harnesses and cable assemblies to customer drawings and samples. The range includes connector-ended leads, ring-terminal cables and branched harnesses. Connectors and cable can be ordered on their own.

JTY harnesses go into energy storage systems, solar and charging equipment, drones, robots, industrial machines and data center power. When a harness uses a JTY connector, a fit problem is traced in one plant.

JTY production staff at cable assembly workstations
Established in
2015
Factory
2,000 m²
Employees
50+
Assembly lines
10
Vertical injection molding machines
30+

Made in JTY's Plant

JTY operator crimping a cable terminal on a crimping machine

Terminal Crimping

JTY crimps terminals on automatic terminal machines and bench crimp presses. First samples come with a crimp cross-section report. You see how each terminal type is compressed before you approve the sample.

JTY production staff assembling cables and connectors

Harness Assembly

JTY builds shielded harnesses. Automatic housing-insertion machines and manual stations fit the terminated wires into connector housings. The wire and connectors listed on the drawing are sourced by JTY. Customer-supplied connectors can be assembled as well. An alternative connector or cable proposed by JTY enters production only after you approve it.

Vertical injection molding workstations in the JTY workshop

Injection Molding

JTY's molding workshop forms custom cable ends, including the molded ends on IP67 waterproof harnesses. A new mold carries a separate mold charge. A stock connector housing needs no new mold.

Batch production takes about 30 days after order confirmation. The same JTY engineers follow a project from drawing review to repeat orders.

See the Drawing-to-Batch Process

Quality & Testing

JTY can load a sample at your working current and measure its temperature rise before the wire size is fixed.

Electrical Checks

JTY can check continuity, polarity and pin assignment on finished harnesses. A swapped or open pin shows up at this check. JTY measures circuit resistance with a precision tester. High resistance points to a poor crimp or contact. JTY tests the insulation between circuits at withstand voltage.

Dimensions & Crimps

JTY measures terminal, crimp and molded-end dimensions on a 2D optical instrument. Ground crimp sections show conductor fill and insulation grip on each terminal type.

Mechanical & Environmental Tests

JTY can run bending tests on moving harnesses and torsion tests on robot harnesses. JTY measures mating force over repeated insertion and withdrawal cycles. Salt spray, damp heat and high/low temperature aging test harnesses for outdoor and energy storage use. A RoHS spectrometer screens materials for restricted substances.

JTY operator at electronic load test equipment
JTY operator at a 2D optical measuring instrument
Salt spray test chamber
See Manufacturing & Quality Control

Working with Your Team

Temporary reference photo of visitors reviewing wiring assemblies

Drawing & Component Review

Start with a drawing or an existing assembly sample. Specify the connector at each end, cable lengths, branch positions and pin assignments so the assembly requirements can be reviewed together.

We discuss any differences between the drawing and sample, missing dimensions and inspection requirements before the assembly requirements are agreed. Quantities and delivery requirements are reviewed for the order.

Temporary reference photo of visitors beside factory assembly workstations

Sample Review & Production

Fit the sample in your equipment to check connector mating, cable routing and access to each termination. Use that review to identify changes needed before you approve the assembly for batch production.

Agree the inspection items and acceptance criteria for your project, including continuity, polarity, pin assignment and any required dimensional checks.

Our Partners

Certificates

ISO 9001
IATF 16949
ISO 14001
UL
TÜV

Contact Us

Tell JTY about your connector, wire harness or cable assembly project. Share the drawings, specifications or sample details you have for an initial review.

    No file selected

    PDF, XLSX, CSV, JPG or PNG · up to 5 MB. Need an NDA? Mention it above.

    Samples in 3–7 days. Batch production about 30 days after order confirmation.

    * Required fields

    Concept illustration of a wire harness sample beside a drawing and inspection checklist Your Project
    PRODUCT CONCEPT