JTY assembly example
Silver multi-contact circular plug with labelled connector-ended and terminal-ended leads

JTY assembly example

Cable Assembly Examples

Compare the end connections and termination formats in these JTY assembly examples.

Multi-Contact Breakout Harness

Silver circular multi-contact plug connected to labelled branches with compact connector housings and terminal-ended leads

Controller, Joints & Tool Connections

Compare each connection as a separate assembly or as part of a wider harness. The drawing or sample establishes the interfaces and the work included in the quoted unit.

Illustration of a robot arm, controller and example external cable route
Application illustration: an example external cable route.
010203
Connection-path illustration.

A controller-to-base lead can be quoted as a separate assembly between the two specified interfaces. JTY builds the lead to the agreed drawing or sample, using the connectors listed on the drawing or supplied by the customer. The quotation identifies the finished ends and any end agreed to be supplied unfinished for equipment-side termination.

The drawing identifies the reference points used for the finished lead length.

An arm-internal harness can combine the power, brake and feedback circuits shown on the drawing. The quoted assembly identifies its branches, finished ends and required shield terminations. JTY assembles the specified or customer-supplied connectors; the equipment design defines the interfaces and the division between fixed and moving sections.

The drawing records connector orientation and cable exit direction.

Where the equipment design already has a wrist disconnect, the segment between that point and the tool can be quoted as a separate replacement or purchase. The quotation identifies its tool-side connector, circuits and branches. The equipment owner or OEM determines whether that existing break point permits the segment to be replaced independently.

The customer checks connector location and wrist clearance on the sample and shares any required drawing changes.

Circular plug with sheathed cable and labelled ferrule-ended leads
JTY assembly example: circular plug and ferrule leads
Multi-contact circular plug with labelled branches
JTY assembly example: multi-contact plug and labelled branches

Bending and Torsion Requirements

Mark each moving section on the drawing. Specify the cable, end terminations, fixed points and motion at each joint.

Fixed pointFixed pointActive cable lengthChanging bend
Moving-section illustration.
Route dutySpecify on the drawingSample check
FixedAnchor points and strain reliefVerify the installed radius and clearance at connectors and clamps.
Repeated bendDynamic bend radius, travel, cable support, cycle target, jacket material and operating temperatureMark the bend zone and check the route at both ends of travel.
TorsionTwist angle, active cable length and speedMark the free length between clamps and record twist over that length.
Bend and twistCombined motion and duty cycleAgree on the sequence, cycle count and acceptance criteria for the finished sample.

Give the cable outside diameter, jacket material, operating temperature and space around the joint. State the bend or torsion cycle target and define the acceptance criteria for the terminated assembly.

Check clearance through travel

Review the full route with the sample installed. Check moving loops, exits, clamps and connector fit at both limits.

Define the sample acceptance record

Record the assembly revision, flex and torsion conditions, cycle count and any required continuity, abrasion or terminal retention checks.

Drawing Release & Trial Fit

The drawing and sample establish the finished assembly, the equipment-side work and the checks agreed for the order.

01

Pass-Through & Termination Sequence

Whether the finished connector can pass through the narrowest opening determines the installation sequence. When both ends fit, the drawing can call for a complete lead. If an end needs termination after pass-through, JTY and the customer assess the drawing or sample and agree the feasible supply and equipment-side termination before quotation. The customer checks clearance on the sample.

Connector envelopePass-through opening
Installation-sequence illustration.
Close view of the multi-contact plug, cable exit and labelled branches
JTY assembly example: connector body, cable exit and labelled branches
02

Supply Boundary

The quoted BOM identifies the cable assembly, specified connectors and any customer-supplied parts included in the unit. A harness drawing may also refer to carriers, hoses or brackets outside that unit. The quotation identifies any separately agreed items and quantities, giving purchasing a defined scope to compare.

03

Assembly Checks & Equipment Validation

JTY checks the sample against the wiring schedule, dimensions and connector orientation agreed for the order. The equipment owner, OEM or integrator checks installation and movement on the robot and shares trial-fit findings.

JTY and the customer review any resulting changes to lead or branch length, connector orientation or termination. The approved sample and agreed drawing revision define the subsequent production build.

Replacement & Extension Questions

Existing disconnect points and the robot’s service instructions determine the replacement boundary. Identify the affected assembly and both adjoining interfaces.

Contact Us

Tell JTY about your connector, wire harness or cable assembly project. Share the drawings, specifications or sample details you have for an initial review.

    No file selected

    PDF, XLSX, CSV, JPG or PNG · up to 5 MB. Files go to the JTY inquiry team for project review and quotation. For an NDA, send a non-confidential summary first and arrange file transfer with us. Inquiry privacy notice.

    Samples ship 3 to 7 days after the drawing is confirmed. Batch production takes about 30 days after order confirmation.

    * Required fields

    Concept illustration of a wire harness sample beside a drawing and inspection checklist
    PRODUCT CONCEPT