
Connector, wire harness & cable assembly manufacturer
JTY makes its own connectors, crimps the terminals and molds the cable exits in the same plant. Samples are ready in 3–7 days. You fit the sample in your equipment before batch production starts.
Our Company
JTY Connector was founded in 2015. In 2021, the company began developing and producing harnesses for new energy applications. JTY works with equipment manufacturers from prototype development to batch production.
JTY makes its own energy storage connectors and bolt connectors. JTY also builds wire harnesses and cable assemblies to customer drawings and samples. The range includes connector-ended leads, ring-terminal cables and branched harnesses. Connectors and cable can be ordered on their own.
JTY harnesses go into energy storage systems, solar and charging equipment, drones, robots, industrial machines and data center power. When a harness uses a JTY connector, a fit problem is traced in one plant.

- Established in
- 2015
- Factory
- 2,000 m²
- Employees
- 50+
- Assembly lines
- 10
- Vertical injection molding machines
- 30+
Made in JTY's Plant

Terminal Crimping
JTY crimps terminals on automatic terminal machines and bench crimp presses. First samples come with a crimp cross-section report. You see how each terminal type is compressed before you approve the sample.

Harness Assembly
JTY builds shielded harnesses. Automatic housing-insertion machines and manual stations fit the terminated wires into connector housings. The wire and connectors listed on the drawing are sourced by JTY. Customer-supplied connectors can be assembled as well. An alternative connector or cable proposed by JTY enters production only after you approve it.

Injection Molding
JTY's molding workshop forms custom cable ends, including the molded ends on IP67 waterproof harnesses. A new mold carries a separate mold charge. A stock connector housing needs no new mold.
Batch production takes about 30 days after order confirmation. The same JTY engineers follow a project from drawing review to repeat orders.
See the Drawing-to-Batch ProcessQuality & Testing
JTY can load a sample at your working current and measure its temperature rise before the wire size is fixed.
Electrical Checks
JTY can check continuity, polarity and pin assignment on finished harnesses. A swapped or open pin shows up at this check. JTY measures circuit resistance with a precision tester. High resistance points to a poor crimp or contact. JTY tests the insulation between circuits at withstand voltage.
Dimensions & Crimps
JTY measures terminal, crimp and molded-end dimensions on a 2D optical instrument. Ground crimp sections show conductor fill and insulation grip on each terminal type.
Mechanical & Environmental Tests
JTY can run bending tests on moving harnesses and torsion tests on robot harnesses. JTY measures mating force over repeated insertion and withdrawal cycles. Salt spray, damp heat and high/low temperature aging test harnesses for outdoor and energy storage use. A RoHS spectrometer screens materials for restricted substances.



Products by Application
Energy Storage
Battery connectors, high-voltage harnesses, BMS sensing harnesses and battery cable assemblies.
View ProductsRenewable Energy
Solar connectors, solar string harnesses, PV cable and charging equipment cable assemblies.
View ProductsDrones & UAVs
Industrial and agricultural drone harnesses, plus UAV payload cable assemblies.
View ProductsRobotics
Wire harnesses for AGV and AMR equipment, robot arms and collaborative robots.
View ProductsIndustrial Automation
Control panel harnesses and sensor, Ethernet, fieldbus, machine-vision and servo/encoder cable assemblies.
View ProductsData Centers & AI
Ring-terminal and connector-to-terminal power cables, plus multiwire, branched and panel-mount assemblies.
View ProductsWorking with Your Team

Drawing & Component Review
Start with a drawing or an existing assembly sample. Specify the connector at each end, cable lengths, branch positions and pin assignments so the assembly requirements can be reviewed together.
We discuss any differences between the drawing and sample, missing dimensions and inspection requirements before the assembly requirements are agreed. Quantities and delivery requirements are reviewed for the order.

Sample Review & Production
Fit the sample in your equipment to check connector mating, cable routing and access to each termination. Use that review to identify changes needed before you approve the assembly for batch production.
Agree the inspection items and acceptance criteria for your project, including continuity, polarity, pin assignment and any required dimensional checks.
Our Partners






Certificates





Contact Us
Tell JTY about your connector, wire harness or cable assembly project. Share the drawings, specifications or sample details you have for an initial review.
Your Project